Waveform-Generators • Digital Logic Output Module Rigol DG-POD-A •
The Rigol Logic Signal Output Module with 16-channel data outputs and 2-channel clock outputs turns the DG2000, DG3000 and DG5000 series into a practical and meaningful Mixed Signal Generator (MSG).
The logic outputs can be configured according to user's needs for specific timing of digital signals. The outputs can be used as logic circuit signal sources, for testing and analysis of the logic circuit designs.
General digital signal protocols can be constructed easily and in conjunction with the analog channels, real life mixed signals can be produced.
Special Features
The Logic Signal Output Module has the following function features:
- Module operation can be turned “ON” or “OFF”
- Two operation modes: “Depend” and “Independ”
- Two trigger modes: Auto and Burst
- Four protocols: RS232、I2C、SPI and PO
- User-defined protocol output based on PO protocol
- A variety of code pattern outputs: All „0" , All „1", „01" turn, IEEE standard pseudorandom sequence
- Online data editing of protocols
- Arbitrary output rate in the “Depend” work mode
- User-defined channels output, including data and clock lines (choose from 16+2)
- Digital channel and analog channel outputs and respectively setting of channels output or not
- Provide TTL, LVTTL, CMOS, LVCMOS and user-defined output voltage
- Remote configuration
- Embedded help
Common Data
-
Output ModuleDigital Logic Output Module Rigol DG-POD-A
-
Interfaces- Port for DG2000/DG3000/DG5000 connection
- 18 digital outputs (16 logic signals and 2 clock signals)
- 40 PIN analog output (22 GND, 16 logic signals and 2 clock signals) -
Dimensions240 mm × 155 mm × 45 mm
(9.45" × 6.1" × 1.77") -
Weight0.718 kg (1.58 lbs)
Details
The complete list of technical specifications you can find in chapter 5 "Specifications" of the manual.
-
FunctionDigital Logic Output Module Rigol DG-POD-A
-
Channels16 logic and 2 clock channel
-
Digital Voltage Range1.4 V - 4.2 V (typical & user-defined, except RS-232)
-
Trigger ModeAuto, Burst
-
Code PatternAll „0"
All „1"
„01" turn
pseudorandom sequence
user data
-
User Space256k Bytes online-edit
2M Bytes output (with Ultrawave software) -
PO-Protocol
-
Analog Voltage Range1.4 V - 9.4 V
-
Clock Phase0°, 90°, 180°, 270°
-
Transmission Rate1bps - 100Mbps
-
Data Output Range1Byte - 128k Bytes
-
I²C-Protocol
-
Analog Voltage Range1.4 V - 9.4 V
-
Bit SequenceMSB
-
Transmission Rate1bps - 15Mbps
-
Data Output Range1Byte - 10k Bytes
-
SPI-Protocol
-
Analog Voltage Range1.4 V - 9.4 V
-
Bit SequenceMSB
-
Transmission Rate1bps - 60Mbps
-
Data Output Range1Byte - 40k Bytes
-
SPI TypeSPI2, SPI3
-
TFSFS_H
FS_L
LD_H
LD_L
NONE -
RS-232-Protocol
-
Analog Voltage Range2.0 V - 4.5 V / -4.5 V - -2.0 V
-
Bit SequenceLSB
-
Transmission Rate1bps - 60Mbps
-
Data Output Range1Byte - 35k Bytes
-
Verification ModeNone, Odd, Even, Fixed0, Fixed1
-
Stop Bits1Bit, 1.5Bit, 2Bits
Batronix.com
Batronix Special: