Adapter and Plugs

The set consists the following attenuators:

• 3 dB RF attenuator, tolerance: ± 0.5 dB
• 6 dB RF attenuator, tolerance: ±0,5 dB
• 10 dB RF attenuator, tolerance: ±0,5 dB
• 20 dB RF attenuator, tolerance: ±0,8 dB
• Frequency range: DC..3 GHz, VSWR <1,2
• load-bearing capacity: 2 W at -55 to 70°C
• Connections: N-plug to N-socket

The set consists of six 1 watt attenuators and two 50 Ω terminators:

• 3 dB attenuator 1 W, tolerance: ± 0.5 dB
• 6 dB attenuator 1 W, tolerance: ±0,5 dB
• 10 dB attenuator 1 W, tolerance: ±0,5 dB
• 15 dB attenuator 1 W, tolerance: ±0,5 dB
• 20 dB attenuator 1 W, tolerance: ±0,8 dB
• 30 dB attenuator, tolerance: ±0,8 dB
• Frequency range: DC..6 GHz, VSWR <1,2
• 2 x 50 Ω terminators
• Connections: SMA-plug

The set consists of four 10 watt attenuators:

• 3 dB RF attenuator, tolerance: ±0.5 dB
• 6 dB RF attenuator, tolerance: ±0,5 dB
• 10 dB RF attenuator, tolerance: ±0,5 dB
• 20 dB RF attenuator, tolerance: ±0,8 dB
• Frequency range: DC..3 GHz, VSWR <1,2
• load-bearing capacity: 10 W at -55 to 70°C, bis 125°C to max. 5 W
• Connections: N-plug to N-socket

SMA connectors, DC to 1 GHz, 50 Ohm/1 W

SMA connectors, DC to 1 GHz, 50 Ohm/1 W

SMA connectors, DC to 1 GHz, 50 Ohm/1 W

SMA connectors, DC to 1 GHz, 50 Ohm/1 W

SMA connectors, DC to 1 GHz, 50 Ohm/1 W

Attenuator 100 W, 20 dB, DC - 2 GHz, low surface temperature.

• Connections: N-plug to N-socket

Attenuator 100 W, 30 dB, DC - 2 GHz, low surface temperature.

• Connections: N-plug to N-socket

Attenuator 50 W, 20 dB, 50 Ohm, 0 to 6 GHz, CE standard.

• Connections: N-plug to N-socket

TBLM01 - Line Impedance Stabilisation Network Mate

High Power 30 dB Attenuator with type N connectors
( input plug / output jack ) and a bandwith of DC to 3 GHz, 50 Ohm/100 W.

BNC connectors, DC to 1 GHz, 50 Ohm/1 W

Feed-through terminator, BNC connectors, DC to 1 GHz, 50 Ohm/1 W

The R&S FSH-Z29 calibration standard is specially designed for field use. It combines all calibration standards (open, short, 50 ohm load) necessary for scalar or vector network analysis as well as DTF measurement. Hung around the user's neck, it is always handy when needed for a calibration.

• Load/short/open
• calibration standard for FSH4/8
• DC to 4GHz, N connector

12 V vehicle power adapter for portable digital oscilloscopes RTH1002 and RTH1004.

44 x 50 Ω coaxial adapter (N type, BNC, RCA, SMA, SMB):

R&S® RT-ZA11 Adapter Plug, BNC to double Banana socket.

Female multipoint connector w. ejectors, 8x2 pin black, spacing 3.5mm / 0.138 in for R&S® HMC804x.

Adapter from SMB Plug (female) to BNC Plug (female) with a very good performance from DC up to 1 GHz. At frequencies above 1 GHz, we recommend that our customers avoid using BNC adapters and cables, as their return loss and repeatability suffer. At these frequencies, the SMA Probe Adapter is a better choice.

One Adapter from SMB Plug (female) to SMA jack (female) with a very good performance from DC up to 6 GHz.

Adapter from BNC plug (male) to SMA jack (female).

Adapter from N-plug (male) to BNC jack (female). Used e.g. to connect a BNC cable to a spectrum analyzer.

Adapter from N-plug (male) to SMA jack (female). Used e.g. to connect the 110A probe cable to a spectrum analyzer.

Additional adapter for Rigol Spectrum Analyzers.

1x N-Female to N-Female 1x N-Male to N-Male 2x N-Male to SMA-Female 2x N-Male to BNC-Female 1x SMA-Male to SMA-Male 1x SMA-Female to SMA-Female 1x 50 Ohm SMA Terminator (1x SMA-Male) 1x BNC T-Connector (1x BNC-Male to 2x BNC-Female) 1x 50 Ohm BNC Impedance (1x BNC-Female to 1x BNC-Male)

Additional attenuators for Rigol Spectrum Analyzers.

1x ATT12061L, 6 dB Attenuation, DC to 12.4 GHz 2x ATT12101L, 10 dB Attenuation, DC to 12.4 GHz

50 Ohm to 75 Ohm impedance transformer for Spectrum Analyser

2x 50 Ohm N Type (male) - 75 Ohm N Type (female)